192.168.1.254 - 192.168.l.254 Router Admin Login & Password

192.168.l.254 IP Address – Default Router Admin & Login Password

The IP address 192.168.1.254 is a private IP address which means it will fit up to a certain range which is reserved from IANA as a private range. Generally, when we purchase a new router or modem they provide username and password. This username and password will protect you from unnecessary connections.

But sometimes there are certain cases which we come across with forgetting the password of our own router or modem. So what can you do at that time, I guess you might be so much worried because you cannot access your router. But you don’t need to worry, in today’s post I am going to give you some guides and tips which will help you to solve all these kind of problems and you will be able to change your password very easily.

192.168.1.254 IP Address Login Admin Password:

192-168-1-254

The IP address 192.168.1.254 codes are a private IP address, and this IP address can be only used for IPv4 address, it cannot be used for Ipv6. This IP address is used as a factory default IP address for a large number of routers and cable modems or wireless modems. This IP address will help you to access to your routers but due to some problem, you may be not able to access it through. There are some routers and modems ever which are compatible with IP address 192.168.1.1 and 192.168.1.254 IP; the only difference is in the last three digits.

This IP address 192.168.1.254 is mostly used by modern routers such as Linksys switches, 2Wire routers, TP-Link routers Alcatel ADSL Modems, Thompson ADSL routers, Westell ADSL Modems, 3Com routers, ADSL billions of routers, SRW2023 and many more routers.

What should you do if you Forgot your IP address Username and Password?

Whenever you purchase a new router or modem, you will get a default login username and password. But if someone has changed it or if you have forgotten your username or password you need to reset your router to factory default settings.

But always keep in mind that, if you reset your router, it will turn to factory defaults and you will lose all your settings.

Step 1: First of all you need to turn off the router.

Step 2: Now you have to press and hold the reset button on the rear panel but to do that you need a pointed pin, a needle or compass and then turn on the router. But do not release the reset button and you have to keep on holding the button for around 5- 10 seconds after turning on your router.

Step 3: Now you can release the button and wait for the device to reboot.

Step 4: Now you can connect your computer to your router through a network cable or by using a Wi-Fi connection.

Note some important points:

Always make sure that your router is powered on before it restarts completely.
Try with your default IP address and enter your default username and password as “admin”.
Make sure that the IP address of your computer is within the same subnet of your router device which means the subnet mask should be 255.255.255.0 and the default gateway should be same with the IP address of your router.

How to Change IP address of your Router:

If you are getting so much problem and difficulty in changing your username or password, then you don’t need to do that. You can simply change the IP address of your router. As I have already told you earlier that IP address 192.168.1.254 codes are private IP address and this IP address can be only used for the IPv4 address.

But this IP address can also be changed if you want to. First of all, you need to check the instructions for your router, but most of the routers need to login to its web control panel. To do that, type your router IP address into the browser window. Then go to the LAN settings to change your required IP address. You also have to go in DHCP settings and type your new IP address which will become your new IP address.

Final Words:

Finally, I would like to tell you that if you are facing any problem regarding the password of your router then follow these instructions which I have mentioned above. I hope you like this article and if you have anything to say then you can freely leave your comment.

How to Fix Troubleshoot Problems in Windows 10, 8.1 & 7

We use Wi-Fi routers to get Wi-Fi connection using our broadband in various devices. But sometimes we might face lots of problems which might prevent dust to connect our broadband to the router or even unable to get the Wi-Fi signal in various devices. In this article, we will discuss fixing and troubleshooting such wi-fi problems.

This problem may arise due to different factors, it may be happening because of software issue or maybe due to some hardware issue. Head down to our guide section to learn more about troubleshooting various wi-fi problems.

Steps to Fix and Troubleshoot Wi-Fi Problems:

These are the various steps which will help you to fix and troubleshoot wi-fi problems on your devices. Read the full manual carefully before applying it with your devices.

Also Read: 192.168.1.254 IP

1. Checking of LAN and WAN Connections:

The best way to rectify this error is you need to check the wireless access point all router ports make sure that the cable sir tightly inserted and LED lights are lit up on both ends.
In any case, The lights are Not lit up in the cable try to swap the LAN cables to make sure they are not damaged. To check that the LAN cable sir damaged or not you can always use the AP checker device.
Also, make sure that you have not connected the WAN cable in the land port out the LAN cable in the WAN port.

2. Wireless Adaptor Verification:

Which time when the wireless network is connected to your network connection control panel it will show that the status is enabled. in case is not showing enable status, then right click on WiFi connection name and enable it. This type is applicable to the windows client.
for the Apple iOS client go to the settings to verify the connection is ready to connect or not or if the airplane mode is on an iPhone or iPad.
in case of Android client, you can verify by going to the Android smartphone that the airplane mode is on or not. On the Wi-Fi is getting connected on reading the signal from the router or not.

3. Router and access point settings verification:

At first, try to locate the SSID which were trying to troubleshoot, you may be getting two radio bands which are 2.4 GHz and. 5 GHz.
Make sure that the IP subnet is assigned to your SSID to get the successful connection.
Also, you need to identify the router IP address which should get connected to the subnet.
Lastly, make sure that the routers event log or the GUI is verified to the IP address from the subnet which is assigned for your Wi-Fi client when it is connected.

4. TCP/IP settings Verification:

Go to the network connection code panel and check the wireless network adapter is showing the status still disable or not. If yes then again try verifying the wireless adaptor.
In case the status is showing it is not connected then select your network name and click on connect option.
While trying to connect the status of your connection may show authenticating and then connected, make sure that your IP addresses assigned to the client IP. To check that click on the diagnose option.

Also Read: 192.168.l.254 Admin Login Password

Final Words

We have gathered videos of information about the issues and its troubleshooting methods of wi-fi problems and provided them in this article for you. We have also provided the complete steps to fix and troubleshoot various wi-fi problems in this article. Share this informative article with other wireless router uses so that they can also get rid of these problems by fixing or troubleshooting various wi-fi problems in their devices.

Tenda Router : Wireless Router Login & Setup Guide

Tenda router is one of the trusted router brands available in the market around the globe. Tenda is one of the router brands with reliable products for accessing the wireless connections by using your network in various devices. But to access it in a device you need to set up and configure the Tenda router before you can have the wireless connection for your devices.

In this article, we will talk about logging and setting up of Tenda router. This process is workable in any Tenda router models around the globe.

The complete guide to set up the Tenda wireless router with the broadband:

Use these following steps to set up the Tenda wireless router using the broadband. The steps usable in any Tenda router models around the globe. Write the steps carefully before going forward with setting up your Tenda router.

First, you need to connect your Tenda router with power outlet and insert the WAN cable into the router to get it connected with the broadband connection.
Now you can either get it connected using the wireless connection or you can connect your Tenda router to your computer using the LAN cable in any one of the four ports available in the Tenda router.
Now open any web browser in a computer and type this in your address bar of that web browser http://192.168.0.1
Once you hit enter the Tenda default IP address will open up and get ready for you to set up according to your broadband network to use it in your device.
Now it will ask you to enter default username and password to get access to the tender setup wizard.
Input ‘admin’ for the username and also type ‘admin’ for the password.
Not in the setup wizard will open up, click on the next button to continue with your configuration for Tenda router.
Now on the left panel locate the WLAN settings and click on it.
Under WLAN settings, select the basic settings to configure the Tenda router.
Now click on the enable wireless checkbox to activity and enter a name for your router in the field where is labeled as “SSID”. By default the name of the network will be the name of the router manufacturer which is tender, change according to your choice and click on the apply button.
Now click on the security settings just below the basic settings option.
Now on the security settings page select any security mode and enter the password for your wireless network.
Select the AES under the WPA algorithm and change the past phrase and click on the apply button to continue.
Now click on the WPS settings and click on the disable option and click on the save button to continue.
Now click on the system tools and change the default username and password from admin to your preferred username and password. Make sure to write it down somewhere, as the default username and password will be changed for your router settings and cannot be accessed with the default username and password provided by the Tenda routers.
Click on the apply button and close the Tenda configuration page. Now you are ready to use your wireless connection using the tender routers.

Also Read: 192.168.1.254 IP

Conclusion:

We have gathered various information about tender wireless routers from their official website and various causes of the internet and list them in this article for you. We have also provided the complete guide to successfully set up in login into your Tenda router using your broadband connection in any devices. Share this article with other Tenda router users so that they can also easily log in and configure their router using these following guide in this article.

How to Find Router IP Address on Windows & MAC OS

Default IP address of your router is easy to find in case you are not having the IP address written on the bottom of the router. Default IP Address lets you access the web interface of the router to modify various aspects of the router connection. In this article, we have provided the complete guide to find the routers default IP address in any devices.

Guide to find the Router Default IP address on Windows:

Use these following methods to find router default IP address on Windows PC.

Method 1:

Open command prompt box from the start or press the Ctrl + R keys to open the run box. Type ‘CMD’ and press enter in the run box and press enter to open the comment on in your Windows PC.
In the command prompt window type, this following command ‘ipconfig’ and press enter.
Now you will get to see the default IP address of your router next to the default gateway and it will be starting with 192.168.

Method 2:

On the taskbar click on the network icon on the button right side not the screen on your Windows PC.
Now right click on the icon and you will get two options, from there select the open Network and sharing center option.
Once the settings page opens up, click on the link beside the connections and then click on the details option.
Now you will get to see the default gateway beside the IPv4, which is the default IP address of a router.

Also Read: 192.168.1.254 IP Login

Guide to find the Router Default IP address on MAC:

Use this following guide to find the router default IP address on Mac OS X.

Method 1:

On your Mac computer go to the utilities and then to the terminal.
Once the screen opens up type this following, netstat -nr | grep default
Now you will get to see the default IP address of a router next to the ‘default’.

Method 2:

Go to the Apple menu and then open the system preferences from there.
On the system, preferences click on the network references option.
No select on the Wi-Fi option If you are using a wireless connection, in case you are using broadband then click on the LAN option.
Now click on the advanced > TCP/IP, now you will get to see the default IP address of a router next to the router option.

Guide to find Router Default IP address on Android:

Use these following steps to get your default IP address of a router using your Android device or tablet.

Go to the device settings > network > Wi-Fi.
Now click on the router Wi-Fi network and you will be able to see the complete details about connected Wi-Fi network including the signal strength, security, link speed and as well as the IP address.

Guide to Find Router Default IP Address on iOS:

Use this following guide to find the router default IP address on any iOS devices.

Go to the settings of your iOS devices and select the Wi-Fi.
Now click on the ‘i’ beside the Wi-Fi network of your router which is connected with iOS devices.
You will see the default IP address next to the router.

Final words:

We have researched about various methods to get the default IP address off the router network using any devices and provided them in this article for you. We are provided the complete guide to find the router default IP address in Windows PC, Mac OS X, iOS devices and Android devices. Share this article with router users so that they can also get know about the default IP address of the router.

How To Login in to a Netgear Router – Router Login Steps

Now you can control your Netgear router and configure it according to your needs. There are tons of things you can do with your router settings which can give greater control and optimization for your use-case. Configuring it according to your needs give greater security and sometimes, a faster internet experience. You can change your router’s default username and password, the number of devices connected to it or add parental guidance control. For all that, you’ve to first log in to your router. Let’s see how to do that and access all the settings.

Logging into your Netgear Router:

netgear router login

Connect your device to the router. You can use your smartphone (Wi-Fi) or your laptop (Wi-Fi or Ethernet) for that purpose. If you’ve forgotten your Wi-Fi password then you will have to connect using an Ethernet cable.
Once connected, open an Internet browser and enter any of the following link: http://www.routerlogin.com, http://192.168.1.1 or http://192.168.0.1
Now you will be directed to an admin login page. There will be two input boxes, one for Admin ID and the other for password. Note that this password will be different from your Wi-Fi password.
If this is your first time logging in, you will have to enter the default credentials. It is advisable to change them so that no one else can log in to the router. The default login ID for a Netgear router is: admin and the password is: password.
Hit Login. You might be prompted for a software update. Let it finish and Login again.

Netgear Router Login

Once you have successfully logged in, you will be able to see the various subsections on the left pane:

Home: Here you can check some basic statistics for your connection. You can see the strength of your connection, the Wi-Fi name (SSID) and password, number of devices connected, parental control, etc.
Internet: Here you can configure your connectivity to the Internet. You can select a Static IP, Subnet, and Gateway or you can keep it dynamic, based on your ISP. You can configure DNS address. If you think your internet is working slower than expected, try changing
your DNS to Google’s public DNS address – Primary: 8.8.8.8 and Secondary: 8.8.4.4. Some routers come with physically hard-coded MAC Addresses whereas the newer ones have software assigned MAC addresses.
Wireless: Most of the settings which you might be looking for can be done from here:
Changing your SSID: If you want to change your Wi-Fi broadcast name then you can do it from here. Simply enter the desired name in front of SSID and hit apply. You can also have a hidden SSID for more security. You will have to reconnect all your devices to the router after changing the SSID.
Changing your Password: If you want to change your Wi-Fi password then you can do that from here. Input the new password in the Passphrase text box and select the Security option. If it is a personal connection, select WPA2-PSK. Some routers may also have an option of WEP which is quite old and deprecated due to its weak encryption.
Changing Operation Channel and Maximum Bandwidth: If you feel your connection is slower than expected, try changing the channel. You can also limit bandwidth to control data usage. A 100 Mbps connection can be throttled down to 2 Mbps or any other amount for that matter.
Parental Control: Parents can also configure this router for controlling content for their children, monitoring internet activity and managing internet on times. First, an OpenDNS account has to made through a small sign up. Once done, you can either select from a list of presets or add your own settings. You can block particular sites, define internet time periods or add floodgates to prevent malicious sites from attacking your network.

Conclusion:

A Netgear router can be configured to your preferences. But one should know that such a facility exists and can be accessed through a simple login procedure. The basic settings discussed above can help make your internet experience much more streamlined and secure.